Cold and heat shock test chamber operation you understand?-LINPIN INSTRUMENT

Cold and heat shock test chamber operation you understand?

Source：LINPIN Time：2024-07-08 Category：Industry NewsNews

Cold and thermal shock test chamber on the market is divided into two categories, one is two-compartment type, including high temperature region and low temperature region, the test object were tested in two different temperatures in the region, alternating hot and cold test; the other is a three-compartment type, in addition to high temperature and low temperature area, there is also a test area, and two-compartment is different, three-compartment does not need to be tested directly in the test area, only through the air compression method, the Two different areas of air compression to the test area can be, compared with the two-compartment type, three-compartment type is easier to operate some of the

Cold and thermal shock test chamber can be used in electronic components, automotive parts, plastics, aerospace, electronic chips, conductors, ceramic magnets and other different types of industries. The principle of the equipment is through the different temperatures, the experimental object for temperature shock test, with a shorter period of time will be a rapid change in temperature to form a test shock, test out the test object in the extreme temperature of the degree of damage, as well as the degree of damage resistance. Usually, the test object in the case of thermal expansion and contraction, will be caused by physical and chemical damage, to test the damage caused by the standard, to further reduce the test object in the extreme temperature of the degree of damage.

The main feature of the thermal shock test chamber is that the temperature can be achieved in a very short period of time to achieve a rapid change in temperature, simulating the natural conditions of the environment, which can be expressed in a few seconds from 100 ℃ high-temperature environment can be changed to minus 60 ℃ of the low-temperature environment, to improve the rate of the test, cost savings.

In different test conditions, the required test equipment is different, according to the actual situation to choose the right equipment. Cold and thermal shock test chamber in the initial development stage, you can find some of the shortcomings of the product early, such as in extreme temperatures to maintain normal operation, in order to improve as early as possible, to prevent the formal commissioning of the larger losses caused by the aftermath of; environment, temperature as a screening conditions, screening out the product performance is a little better.

Previous article: How to test the waterproofness of the rain test chamber

Next article: How the cryogenic test chamber achieves a stable low-temperature environment

News Recommendation

24.07

Focusing on the steel industry, ultra-low-temperature environmental testing is ready to go.

Recently, LINPIN Instruments has successfully won the bid of Baowu Iron and Steel Company Limited's ultra-low temperature reliability environment testing project. This is another cooperation between the company and Baowu Iron & Steel following the cooperation of Anshan Iron & Steel, Hesteel, JISCO, Shagang and other iron and steel companies, which not only reflects the deep trust and tacit understanding established between the two sides in the long-term cooperation, but also lays down a colorful stroke for the diversified cooperation between the company and the iron and steel group.

24.07

The birth of the linear 20℃ degree fast temperature change tester

Enterprises should pay attention to both the needs of users, but also to pay attention to competitors, and strive to find a balance between user needs and competitors marketing concept, known as “market-oriented”, the core of which is from the user's needs Adhere to the market orientation, the pulse of the user, the foothold and the destination point on the basis of the product “sell”, based on the concept, LF Instruments positive development of 20 ℃/min fast temperature change test chamber and successfully introduced to the market. Based on this concept, LF Instruments has developed a 20℃/min fast temperature change tester and successfully introduced it to the market.

24.07

LINPIN Instruments in Action for Large-Scale Equipment Renewal

Recently, China issued the Action Program for Promoting Large-scale Equipment Renewal and Consumer Goods Trade-in (hereinafter referred to as the Action Program), which systematically deploys 20 specific measures around the implementation of the four major actions of equipment renewal, consumer goods trade-in, recycling, and standard enhancement. Since the release of the Action Program, provinces and municipalities have responded to the policy by gradually promoting the relevant work and formulating provincial and municipal plans to promote large-scale equipment renewal and consumer goods trade-in.

24.07

The first quarter “opens with a bang”.

One point of plowing, one point of harvest. At the beginning of the new year, the branches and subsidiaries of LFG have delivered brilliant report cards with successive good news. A white horse passes by, the years go by like a shuttle, what changes is the cycle of time and space, what remains unchanged is the seriousness and persistence of LF people.

24.07

How to test the waterproofness of the rain test chamber

Rain test chamber is a test instrument to test whether the waterproof is good, the figure of this equipment can be said to be everywhere, applied in various places. Small to our usual use of cell phones, flashlights and other lighting apparatus; large to the aerospace industry, lighting systems, signaling device testing and so on. Waterproof has always been a lot of industry can not get around a topic, a lot of equipment once the rain and other wet, its service life will be greatly reduced, this equipment in the waterproof performance test link plays a vital role.